![stb erom upgrade 2.0. 0c download stb erom upgrade 2.0. 0c download](http://www.easy-upload.net/fichiers/image020.20101210134158.gif)
![stb erom upgrade 2.0. 0c download stb erom upgrade 2.0. 0c download](http://heavenlyzero.weebly.com/uploads/1/2/4/0/124018651/795118989.png)
i remember reading somewhere alright that the usb to rs232 cables dont work so i got the proper one with the female connections off ebay for a few euro. Its a rs232 cable with the female connection at either end and i have to connect one end to an old desktop at work and the other end to the back of the 250. are you running in a laptop/pc with true rs233 or a usb to rs232 adaptor as some of these are a bit "sh1te" when transferring f/ware. Thats as far as i have taken it as that's all i have access to.īetter off to put the confirmed f/ware on the compatable boxes. Hi, firmware, like channel lists are not compatable across models, I may be wrong and am open to correction.įrom my experience, A120 don't work on 150 and a 150 don't work on a 250. i will let you know how i get on as it might also be a help to others reading this thread if it works apparently if i had another 250 combo i could connect the two of them together with the null modem cable and get the bricked box working off the good box by turning on the bricked box and the firmware gets sent from the good box to the bricked one and gets it working again, i dont know if this works or not i remember reading it here on this site somewhere but it might help someone else out if they run into the " ASH " problem and have two Ariva boxes the same model but unfortunately i dont have another 250 box and i dont think it would be wise to do it with a 120 box as i have threee of those as i might end up doing more harm than good, anyway thanks for the advice. i will try an older firmware and turn on and off the stb like you said see if that does the trick. I will give that a go on monday as i have to use an old desktop computer at work as my laptop dosent have a RS232 connection. Please reset target", just turn off and on ariva. I also had to turn off and on the stb after it sync'd, to start the flashing process. That happened to me once before, as far as i can remember, but i just flashed an earlier original firmware version and upgraded it then. i know the description of what is happening is long winded but i imagine it might also be of help to others who are trying to sort the " ASH "problem out on their respective boxes.so any ideas what i am doing wrong ?.thanks in advance. I am going around in circles and getting dizzy but achieving nothing so any advice would be appreciated I read on another post to switch the box off and on again to start the flash process but i end up back at the message If i hit the cancel button at the bottom of the screen it saysĭownloading.are you sure you want to cancelīut still nothing happens, nothing downloads, even if i left it there till christmas. The box stays on this setting with nothing happening When i click back and then next without changing any of the settings and leaving the box on i get a message Set my port : to COM 1, BIT RATE : 115200, PARITY : EVEN, OPERATE MODE : UPGRADE and i ticked INCLUDE BOOTLOADER.I then browsed for the ferguson firmware file V1.26B3 abs file which was approx 8mb in size and then hit next ( bye the way my stb was switched off at this stage while entering the information into the erom tool ) after hitting next i turned on the box and got a message " synchronising STBs Done went through the procedure as explained here in another post.
Stb erom upgrade 2.0. 0c download install#
I have bricked or should i say a fellow that was trying to install a patch on it bricked it but thats a touchy subject as i have to try and fix it, anyway i have a 250 Ariva and downloaded the latest firmware from the Ferguson website V1.26B3 and the EROM UPGRADE TOOL 2.0.1.